 Suggested gears for a ford 9 inch 3.55 in a 1974 Jensen Healey
|
702 |
3 |
dlwharleyman |
05/30/2018 01:52PM
Last Post by roverman
|
|
Olds head stamping
|
698 |
4 |
vipert4 |
05/15/2018 08:48AM
Last Post by vipert4
|
|
5 liter v8 using p76 crank and 3.9 liter rover block.
|
684 |
2 |
jagrov |
05/11/2018 10:34AM
Last Post by MGBV8
|
|
Prepping head for high lift cam - springs? Stem seals?
Goto Page: 1, 2 |
1984 |
32 |
turbodave |
05/08/2018 01:51PM
Last Post by turbodave
|
|
|
calculating axle ratios
|
708 |
3 |
BlownMGB-V8 |
05/03/2018 10:43AM
Last Post by BlownMGB-V8
|
|
Geez, need some help
|
864 |
12 |
donkelly23 |
04/24/2018 09:44AM
Last Post by donkelly23
|
|
Stroker P76?
|
818 |
9 |
BlownMGB-V8 |
04/17/2018 06:04PM
Last Post by BlownMGB-V8
|
|
Gear ratio calculator, rear gears, and transmission ratios
Goto Page: 1, 2, 3, 4, 5 |
5907 |
81 |
rficalora |
04/10/2018 09:22AM
Last Post by rficalora
|
|
O2 Sensor Locations
|
799 |
11 |
RDMG |
04/08/2018 12:52PM
Last Post by Blown v8
|
|
Engine Mounts
|
805 |
10 |
Stonesmith |
04/07/2018 03:33PM
Last Post by 302GT
|
|
Can someone explain F1 N.A. engines?
|
818 |
3 |
VirginiaJenkins |
04/07/2018 11:48AM
Last Post by joe_padavano
|
|
|
3.9 rover rebuild
|
864 |
3 |
Bmwrover |
04/04/2018 02:02AM
Last Post by minorv8
|
|
T5 5th Gear "Rattle"
Goto Page: 1, 2 |
2435 |
24 |
Mickey Richaud |
03/16/2018 06:33PM
Last Post by Mickey Richaud
|
|
lifter/cam wear
|
923 |
5 |
joecolli |
02/27/2018 12:35PM
Last Post by roverman
|
|
Oil Filter with Intermediate cover
|
1056 |
1 |
donkelly23 |
02/26/2018 12:11PM
Last Post by donkelly23
|
|
Magnum Gasket Oil Pan
|
1096 |
3 |
donkelly23 |
02/04/2018 02:29PM
Last Post by donkelly23
|
|
Tremec T5 oil leak
|
2179 |
20 |
IaTR6 |
02/02/2018 10:29AM
Last Post by tbo
|
|
Intermediate Cover
|
1328 |
17 |
donkelly23 |
01/21/2018 03:58PM
Last Post by mgb260
|
|
|
Adjusting fuel pressure
|
874 |
3 |
tr7v8mike |
01/21/2018 03:36PM
Last Post by tr7v8mike
|
|
New(?) 7.5lb Rover V8 billet steel flywheel
|
1246 |
8 |
RDMG |
01/21/2018 12:20PM
Last Post by Blown v8
|
|
NEW Holley Sniper 2300 TBI
|
1048 |
1 |
mgb260 |
01/20/2018 04:17PM
Last Post by mgb260
|
|
Moved: Help re Hoyle IFS
|
118 |
0 |
NGTCV8 |
01/13/2018 10:24AM
Last Post by
|
|
Sequence of changes?
|
905 |
14 |
rficalora |
01/09/2018 03:26PM
Last Post by mgb260
|
|
Advice needed on '69 Ford 302 upgrades but retaining 2 barrel carb
|
856 |
7 |
RudyK |
01/05/2018 12:24PM
Last Post by RudyK
|
|
drop base air cleaner for 4 barrel carter 400 cfm carburetor
|
707 |
6 |
blockmom |
01/02/2018 02:54PM
Last Post by 88v8
|
|
|
Aussie Scimitar Build
|
707 |
2 |
mgb260 |
12/31/2017 11:24AM
Last Post by MGBV8
|
|
Ford 302 distributor with 7-1 cam position sensor in it?
|
1154 |
16 |
rficalora |
12/11/2017 05:22PM
Last Post by rficalora
|
|
exhust modifications; resonator tube
Goto Page: 1, 2 |
5997 |
21 |
302GT |
12/11/2017 09:45AM
Last Post by Dan B
|
|
A Different Kind of Dyno...
|
913 |
6 |
roverman |
12/07/2017 02:52PM
Last Post by roverman
|
|
Clutch Sizing?
|
943 |
17 |
RDMG |
12/07/2017 12:11PM
Last Post by MGBV8
|
