Classified Ads: Swap Parts Here!

buy, sell, or trade - cars, parts, tools, etc. (Please keep ads out of the other forums!)

Go to Thread: Previous•Next
Go to: Forum List•Message List•New Topic•Log In


declan
Declan Gardner
St. Louis
(62 posts)

Registered:
05/12/2017 12:28PM

Main British Car:
1969 MGB 1800

SOLD - Firebird rearend narrowed and mounts welded for MGB
Posted by: declan
Date: June 10, 2017 11:31AM

80’s Firebird rear end, 5 lug(bolt pattern same as MGC 5 lug), disc brakes, limited slip, “3:3/1 I think”, and mounts to fit rubber bumper MGB (this may be the same as the chrome bumper?). The brakes will need a proportioning valve in line when you set up the new lines. $1200
rearend1.JPG
rearend2.JPG
rearend3.JPG



Edited 1 time(s). Last edit at 10/30/2017 11:15AM by MGBV8.


maxwedge5281
larry ingram
south carolina
(52 posts)

Registered:
09/23/2014 05:59AM

Main British Car:
59 bn6 zz4 sbc 200 4R aod, 59bn6 302 ford, tremec

Re: Firebird rearend narrowed and mounts welded for MGB
Posted by: maxwedge5281
Date: June 11, 2017 10:00AM

w2hat is the width from bolt on to bolt on surface? i am looking for a narrowed rear for an austin healey 3000. thanks


declan
Declan Gardner
St. Louis
(62 posts)

Registered:
05/12/2017 12:28PM

Main British Car:
1969 MGB 1800

Re: Firebird rearend narrowed and mounts welded for MGB
Posted by: declan
Date: June 27, 2017 01:11PM

53" wide, outermost brackets pictured are 38" apart, innermost are 25" apart.
Get Your BritishV8 T-shirt by clicking here


declan
Declan Gardner
St. Louis
(62 posts)

Registered:
05/12/2017 12:28PM

Main British Car:
1969 MGB 1800

Re: Firebird rearend narrowed and mounts welded for MGB
Posted by: declan
Date: July 24, 2017 07:36PM

$900


MGBV8
Carl Floyd
Kingsport, TN
(4512 posts)

Registered:
10/23/2007 11:32PM

Main British Car:
1979 MGB Buick 215

authors avatar
Re: Firebird rearend narrowed and mounts welded for MGB
Posted by: MGBV8
Date: July 25, 2017 12:00PM

Your ad on MGExp says 52" wide. 53" or 52"?


declan
Declan Gardner
St. Louis
(62 posts)

Registered:
05/12/2017 12:28PM

Main British Car:
1969 MGB 1800

Re: Firebird rearend narrowed and mounts welded for MGB
Posted by: declan
Date: July 25, 2017 07:13PM

52", but I will measure again to be sure.


limey222
Michael Cubbon
Portland, OR
(129 posts)

Registered:
08/01/2015 12:55PM

Main British Car:
1969 MGB GM 3.4L V6

Re: Firebird rearend narrowed and mounts welded for MGB
Posted by: limey222
Date: July 27, 2017 01:20AM

Given the high cost of truck freight for this unit, I would offer $700 for it providing its length is 52" and it is around a 3.3 ratio. My reasoning is that I have been strongly considering a Quaife LSD installed in my MGC 3.07 axle which would cost me about the same once shipping is thrown in.



declan
Declan Gardner
St. Louis
(62 posts)

Registered:
05/12/2017 12:28PM

Main British Car:
1969 MGB 1800

Re: Firebird rearend narrowed and mounts welded for MGB
Posted by: declan
Date: July 31, 2017 10:50PM

Not sure how I miss measured, my flat edge may have been on a stud. Wheel mating surface to wheel mating surface is 50.5".
3 and 1/4 turns of the driveshaft to turn the wheel.
It is a 10 bolt rear end, I am going to try to identify whether it is a 8.2 or 8.5...


MGBV8
Carl Floyd
Kingsport, TN
(4512 posts)

Registered:
10/23/2007 11:32PM

Main British Car:
1979 MGB Buick 215

authors avatar
Re: Firebird rearend narrowed and mounts welded for MGB
Posted by: MGBV8
Date: August 01, 2017 11:13PM

It is neither.

It is either a 7.5" or 7.625" (if '86 or later).


declan
Declan Gardner
St. Louis
(62 posts)

Registered:
05/12/2017 12:28PM

Main British Car:
1969 MGB 1800

Re: Firebird rearend narrowed and mounts welded for MGB
Posted by: declan
Date: August 11, 2017 10:58AM

$800


declan
Declan Gardner
St. Louis
(62 posts)

Registered:
05/12/2017 12:28PM

Main British Car:
1969 MGB 1800

Re: Firebird rearend narrowed and mounts welded for MGB
Posted by: declan
Date: October 01, 2017 01:49PM

$500
I am selling this to help offset the cost of sending a really nice b motor to a shop to be assembled so I can drop that in my car. Someone with a nice v6-or v8 project needs this more than I do.
Get Your BritishV8 T-shirt by clicking here


declan
Declan Gardner
St. Louis
(62 posts)

Registered:
05/12/2017 12:28PM

Main British Car:
1969 MGB 1800

Re: Firebird rearend narrowed and mounts welded for MGB
Posted by: declan
Date: October 09, 2017 09:29AM

Still available. PM me if you need specific information, such as numbers stamped on the housing or need something measured, calculated...


declan
Declan Gardner
St. Louis
(62 posts)

Registered:
05/12/2017 12:28PM

Main British Car:
1969 MGB 1800

*SOLD*Re: Firebird rearend narrowed and mounts welded for MGB
Posted by: declan
Date: October 30, 2017 11:05AM

*SOLD*


Go to: Forum List•Message List•New User Registration•Log In
Sorry, only registered users may post in this forum.