Bodywork, Paint, Interior, Trim, & Wiring

discussions about bodywork, paint, interiors, trim, audio, electrical components, wiring, etc.

Go to Thread: PreviousNext
Go to: Forum ListMessage ListNew TopicLog In


Kernel-K
Bill Kowalewski

(6 posts)

Registered:
08/17/2014 11:04AM

Main British Car:


Relocating Electrics
Posted by: Kernel-K
Date: September 28, 2014 07:06AM

One objective of my planned MGB-V8 conversion is a clean engine bay free of as much wiring/electrics as possible. Apart from the workload required, is there any technical hazard or fault with relocating the fuse box, relays, voltage regulator etc...in the trunk? I'd like to fab a dedicated "panel box" in the trunk for a clean dry installation. Appreciate any lessons learned from the field !


BlownMGB-V8
Jim Blackwood
9406 Gunpowder Rd., Florence, KY 41042
(6468 posts)

Registered:
10/23/2007 12:59PM

Main British Car:
1971 MGB Blown,Injected,Intercooled Buick 340/AA80E/JagIRS

authors avatar
Re: Relocating Electrics
Posted by: BlownMGB-V8
Date: September 28, 2014 08:55AM

Main disadvantage is the size of the wiring bundle from the trunk to the dashboard area.

Jim


Jim Stabe
Jim Stabe
San Diego, Ca
(829 posts)

Registered:
02/28/2009 10:01AM

Main British Car:
1966 MGB Roadster 350 LT1 Chevy

authors avatar
Re: Relocating Electrics
Posted by: Jim Stabe
Date: September 28, 2014 10:49AM

I relocated the PCM behind the drivers seat. It required lengthening about 40 wires with one gauge larger wire and soldering and covering the joints with shrink tubing. To Jim B's point it made for a large bundle but not difficult to manage once bundled.

PCM mounting (2).JPG

Engine install (5).JPG

Another thing you can do to clean up the engine compartment is to route the front wiring (headlights, turn signals, horn, etc) through conduit in the fender wells

Conduit (1).JPG


Kernel-K
Bill Kowalewski

(6 posts)

Registered:
08/17/2014 11:04AM

Main British Car:


Re: Relocating Electrics
Posted by: Kernel-K
Date: September 29, 2014 02:35PM

Thanks all - appreciate the advice. Now back to the wiring diagram...


DonB
Don Bonar
Prairie Village, KS
(80 posts)

Registered:
09/09/2011 10:06AM

Main British Car:
1971 MG-B 95 GM 3.4 V-6

Re: Relocating Electrics
Posted by: DonB
Date: October 09, 2014 10:48AM

Bill,
Think the previous posts hight the high points... Like you, I wanted to "clean up" all those scattered electical connections on the inner fenders. Here are a few tips that you've probably already thought of.

I ran PVC pipe between the inner and outer fenders for all the wiring running to the front. When I pulled the wires thru, I also added two additional cords because I just knew I'd forget something... or later decide to run more, after things got buttoned up. Sure as heck, I had to use one... and stil have a spare. (plan ahead)

Should have used the space inside the rocker pannel frame under the right door, to pass wire to the rear . while I was replacing the rot. (Didn't plan ahead!)

I use the mysterious access holes in the inner fender near the firewall, to mount a modern fuse box with the fancy fuses that glow if blown. (they always blow when it's dark and your flashlight batteries are gone)

Mine is a simple carb engine so didn't have the ECU to deal with... so much easier and smaller. Still don't understand why electricity doesn't run out of the wall and make a puddle, when you unplug something!

Don B.


BlownMGB-V8
Jim Blackwood
9406 Gunpowder Rd., Florence, KY 41042
(6468 posts)

Registered:
10/23/2007 12:59PM

Main British Car:
1971 MGB Blown,Injected,Intercooled Buick 340/AA80E/JagIRS

authors avatar
Re: Relocating Electrics
Posted by: BlownMGB-V8
Date: October 09, 2014 02:11PM

Must be like those air hose couplers. Probably why the outlet end is always bigger.

Jim


danmas
Dan Masters
Alcoa, Tennessee
(578 posts)

Registered:
10/28/2007 12:11AM

Main British Car:
1974 MGBGT Ford 302

authors avatar
Re: Relocating Electrics
Posted by: danmas
Date: October 09, 2014 03:47PM

image.jpg



djw090
David Witham
Warwick UK
(115 posts)

Registered:
06/12/2008 11:20AM

Main British Car:
MGB 1974 and MG ZT 160 turbo 2005

Re: Relocating Electrics
Posted by: djw090
Date: November 06, 2014 08:24AM

On a left had drive car it might be easy to mount a fuse box on the cabin side of the bulkhead behind the glove box. This is very close to where the loom comes from the dash to go through the bulkhead and might reduce your new/lengthened wires to those forward of the bulkhead. The gearbox/overdrive/fuel pump/rear lights part of the loom could go out through the grommeted hole used by the RHD speedo cable.


Sorry, only registered users may post in this forum.