Race Cars and Motorsports

if it's about racing, spectating, performance driving, or race-prep... this is the place

Go to Thread: PreviousNext
Go to: Forum ListMessage ListNew TopicLog In


TR4racer
Michael Deweerd
Woodstock, Ontario Canada
(5 posts)

Registered:
04/29/2011 09:40PM

Main British Car:
1962 TR4 1967 TR4A 1969 GT6 1970 GT6 1980 TR7conv

Huffaker TR8 convertible clone
Posted by: TR4racer
Date: September 08, 2016 10:27PM

Hello Everyone
Well I'm finally starting to start the planning stage of my next car. A Convertible TR8 Race car similar to the Huffaker cars.
I have little to no info on what was used to build these cars so I'm asking the list here to share any knowledge they may have on what parts were used by Huffaker and Group 44

This car will have to be "period correct" so no parts later than 1980 should be suggested.
So far I have a fresh mild 3.5 rover engine Nine inch Ford rear end (I understand Group 44 ran a eight inch ford)
Huffaker fenders front and back Fiber glass hood and trunk lid Roll cage, fuel cell and new cross member and of course a nice convertible donor car.

Some of the information I require.

What Transmission was used?
Period correct rims 8 inch front and 10 inch rear? these look to be five stud so Rim manufacturer? and what front hubs/shocks?
Sway bar?? where to find 1 inch diameter
Rad? custom?
Brakes for the front?
Brakes on the rear? disc or drums?

Any info is appreciated It is not my intent to make an exact duplicate I really want my own car but similar to the black Huffaker cars.

Thanks
Mike


roverman
Art Gertz
Winchester, CA.
(3188 posts)

Registered:
04/24/2009 11:02AM

Main British Car:
74' Jensen Healy, 79 Huff. GT 1, 74 MGB Lotus 907,2L

Re: Huffaker TR8 convertible clone
Posted by: roverman
Date: January 09, 2017 10:59AM

I own "H5" Huffaker TR8 coupe. BL required as many oem and motorsport dept. parts as possible in concert with SCCA rules restrictions. This means oem trans and rear end,(with allowable mods). Racing radiator is brass/copper, heavy and hi-density. Brakes are "AP" disk, frt./rear.These cars are more restricted by rules than Group 44 cars,(different sanctioning body). 4L, 350 hp.,(Joe Huffaker rating). Good Luck. Art G.


MGBV8
Carl Floyd
Kingsport, TN
(4511 posts)

Registered:
10/23/2007 11:32PM

Main British Car:
1979 MGB Buick 215

authors avatar
Re: Huffaker TR8 convertible clone
Posted by: MGBV8
Date: January 20, 2017 08:59AM

No advantage to using a heavier 9 inch Ford rear, IMO.


BlownMGB-V8
Jim Blackwood
9406 Gunpowder Rd., Florence, KY 41042
(6468 posts)

Registered:
10/23/2007 12:59PM

Main British Car:
1971 MGB Blown,Injected,Intercooled Buick 340/AA80E/JagIRS

authors avatar
Re: Huffaker TR8 convertible clone
Posted by: BlownMGB-V8
Date: January 22, 2017 01:48PM

9" would be overkill for anything short of an 8 second car. (MGB)

An axle with an 8-1/2" ring gear will be good for 500 hp in a 4000 lb car. (many applications: Corvette, Viper, Jaguar, Jeep, Dodge, I-H, etc.)

8" is generally considered acceptable for 300 hp in a 2900 lb car. (Maverick)

Gear life is inversely proportional to load but the curve is not linear. Above a certain load point life plummets dramatically.

Jim


piquet
PAT KAYE

(2 posts)

Registered:
11/14/2018 11:44AM

Main British Car:


Re: Huffaker TR8 convertible clone
Posted by: piquet
Date: November 14, 2018 01:07PM

Both of these Huffaker TRs and the TR8 behind them belong to a Curt Johnston in Fairfield, CA. For all the info you're seeking, why not go to Huffaker Engineering's website (link below) check them out on facebook


[www.huffakerengineering.com]
42754152_1788091337955341_6371807313325457408_n.jpg


Sorry, only registered users may post in this forum.